Publications by    
Page 1  (22 Items)

1.  New Infrared Materials and Detectors
M. Razeghi, J.D. Kim, S.J. Park, Y.H. Choi, D. Wu, E. Michel, J. Xu, and E. Bigan
International Symposium on Compound Semiconductors (ISCS-22), Cheju Island, Korea; Compound Semiconductors 145 (8)-- January 1, 1996
 
2.  Background limited performance in p-doped quantum well intersubband photodetectors
J. Hoff, J. Piotrowski, E. Bigan, M. Razeghi, and G.J. Brown
International Symposium on Compound Semiconductors (ISCS-22), Cheju Island, Korea; Compound Semiconductors 145 (8)-- January 1, 1996
 
3.  MOCVD Growth of Ga1-xInxAsyP1-y-GaAs Quantum Structures
M. Razeghi, J. Hoff, M. Erdtmann, S. Kim, D. Wu, E. Kaas, C. Jelen, S. Slivken, I. Eliashevich, J. Diaz, E. Bigan, G.J. Brown, S. Javadpour
NATO 2nd International Workshop on Heterostructures Epitaxy and Devices (HEAD '95) Smolenice Castle, Slovakia; Heterostructure Epitaxy and Devices-- January 1, 1996
 
4.  8-13 μm InAsSb heterojunction photodiode operating at near room temperature
J.D. Kim, S. Kim, D. Wu, J. Wojkowski, J. Xu, J. Piotrowski, E. Bigan, and M. Razeghi
Applied Physics Letters 67 (18)-- October 30, 1995
p+-InSb/π-InAs1−xSbx/n+-InSb heterojunction photodiodes operating at near room temperature in the 8–13 μm region of infrared (IR) spectrum are reported. A room‐temperature photovoltaic response of up to 13 μm has been observed at 300 K with an x≊0.85 sample. The voltage responsivity‐area product of 3×10−5 V· cm²/W has been obtained at 300 K for the λ=10.6 μm optimized device. This was close to the theoretical limit set by the Auger mechanism, with a detectivity at room temperature of ≊1.5×108 cm ·Hz½/W. reprint
 
5.  p-doped GaAs/Ga0.51In0.49P quantum well intersub-band photodetectors
J. Hoff, X. He, M. Erdtmann, E. Bigan, M. Razeghi, and G.J. Brown
Journal of Applied Physics 78 (3)-- August 1, 1995
Lattice‐matched p-doped GaAs–Ga0.51In0.49P quantum well intersub‐band photodetectors with three different well widths have been grown on GaAs substrates by metal‐organic chemical‐vapor deposition and fabricated into mesa structures. The photoresponse cutoff wavelength varies between 3.5 and 5.5 μm by decreasing the well width from 50 down to 25 Å. Dark current measurements as a function of temperature reveal activation energies for thermionic emission that closely correspond to measured cutoff wavelengths. Experimental results are in reasonable agreement with Kronig–Penney calculations. reprint
 
6.  Background Limited Performance in p-doped GaAs/Ga[0.71]In[0.29]As[0.39]P[0.61] Quantum Well Infrared Photodetectors
J. Hoff, S. Kim, M. Erdtmann, R. Williams, J. Piotrowski, E. Bigan, M. Razeghi and G. Brown
Applied Physics Letters 67 (1)-- July 3, 1995
Background limited infrared photodetection has been achieved up to 100 K at normal incidence with p-type GaAs/Ga0.71In0.29As0.39P0.61 quantum well intersubband photodetectors grown by low-pressure metalorganic chemical vapor deposition. Photoresponse covers the wavelength range from 2.5 μm up to 7 μm. The device shows photovoltaic response, the cutoff wavelength increases slightly with bias, and the responsivity increases nonlinearly with bias. These effects are attributed to an asymmetric quantum well profile. reprint
 
7.  Ultraviolet Detectors for AstroPhysics Present and Future
M. Ulmer, M. Razeghi, and E. Bigan
Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 239-- February 6, 1995
Astronomical instruments for the study of UV astronomy have been developed for NASA missions such as the Hubble Space Telescope. The systems that are `blind to the visible' (`solar-blind') yet sensitive to the UV that have been flown in satellites have detective efficiencies of about 10 to 20%, although typically electron bombardment charge coupled devices are higher at 30 - 40% and ordinary CCDs achieve 1 - 5%. Therefore, there is a large payoff still to be gained by further improvements in the performance of solar blind UV detectors. We provide a brief review of some aspects of UV astronomy, UV detector development, and possible technologies for the future. We suggest that a particularly promising future technology is one based on the ability of investigators to produce high quality films made of wide bandgap III-V semiconductors. reprint
 
8.  Investigation of 0.8 μm InGaAsP-GaAs laser diodes with Multiple Quantum Wells
J. Diaz, H. Yi, S. Kim, M. Erdtmann, L.J. Wang, I. Eliashevich, E. Bigan and M. Razeghi
Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995
In this paper, we studied the effects of the active region structure (one, two and three quantum wells with same total thickness) for high-power InGaAsP-GaAs separate confinement heterostructure lasers emitting at 0.8 μm wavelength. Experimental results for the lasers grown by low pressure metalorganic chemical vapor deposition show excellent agreement with the theoretical model. Total output power of 47 W from an uncoated 1 cm-wide laser bar was achieved in quasi-continuous wave operation reprint
 
9.  Aluminum-free Quantum Well Intersubband Photodetectors with p-type GaAs Wells and lattice-matched ternary and quaternary barriers
J. Hoff, E. Bigan, G.J. Brown, and M. Razeghi
Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995
Acceptor doped Quantum Well Intersubband Photodetectors with GaAs wells and lattice matched barriers of both ternary (In0.49Ga0.51P) and quaternary (In0.62Ga0.38As0.22P0.78) materials have been grown on semi-insulating GaAs substrates by Low Pressure Metal Organic Chemical Vapor Deposition. Mesa devices were fabricated and subjected to a series of tests to illuminate experimentally some of the detection capabilities of the lattice matched quaternary InxGa1-xAsyP1-y system with (0 ≤ x ≤ 0.52) and (0 ≤ y ≤ 1). The observed photoresponse cut-off wavelengths are in good agreement with the activation energies observed in the temperature dependence of the dark currents. Kronig-Penney calculations were used to model the intersubband transition energies. reprint
 
10.  Low pressure metalorganic chemical vapor deposition of high quality AlN and GaN thin films on sapphire and silicon substrates
P. Kung, X. Zhang, E. Bigan, and M. Razeghi
Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995
High quality AlN and GaN epilayers have been grown on basal plane sapphire by low pressure metalorganic chemical vapor deposition. The X-ray rocking curve linewidth of the AlN and GaN films were about 100 and 30 arcsecs respectively. Sharp absorption edges were determined at 6.1 and 3.4 eV respectively. Successful donor-bound excitonic luminescence emissions were detected for GaN films grown on sapphire and silicon. Two additional lines at 3.37 and 3.31 eV were observed on GaN on sapphire and assumed to be impurity-related. Doping of GaN layers was achieved with magnesium. Mg-related photoluminescence emissions were successfully detected on as-grown samples, without any post-growth treatment. reprint
 
11.  Analysis of Spectral Response in p-type GaAs/GaInP QWIPs
J. Hoff, C. Jelen, S. Slivken, E. Bigan, M. Razeghi, and G.J. Brown
Superlattices and Microstructures, 8 (4)-- January 1, 1995
 
12.  A detailed analysis of carrier transport in InAs0.3Sb0.7 layers grown on GaAs substrates by metalorganic chemical vapor deposition
C. Besikci, Y.H. Choi, G. Labeyrie, E. Bigan and M. Razeghi with J.B. Cohen, J. Carsello, and V.P. Dravid
Journal of Applied Physics 76 (10)-- November 15, 1994
InAs0.3Sb0.7 layers with mirrorlike morphology have been grown on GaAs substrates by low‐pressure metalorganic chemical vapor deposition. A room‐temperature electron Hall mobility of 2×104 cm²/V· s has been obtained for a 2 μm thick layer. Low‐temperature resistivity of the layers depended on TMIn flow rate and layer thickness. Hall mobility decreased monotonically with decreasing temperature below 300 K. A 77 K conductivity profile has shown an anomalous increase in the sample conductivity with decreasing thickness except in the near vicinity of the heterointerface. In order to interpret the experimental data, the effects of different scattering mechanisms on carrier mobility have been calculated, and the influences of the lattice mismatch and surface conduction on the Hall measurements have been investigated by applying a three‐layer Hall‐effect model. Experimental and theoretical results suggest that the combined effects of the dislocations generated by the large lattice mismatch and strong surface inversion may lead to deceptive Hall measurements by reflecting typical n‐type behavior for a p‐type sample, and the measured carrier concentration may considerably be affected by the surface conduction up to near room temperature. A quantitative analysis of dislocation scattering has shown significant degradation in electron mobility for dislocation densities above 107 cm−2. The effects of dislocation scattering on hole mobility have been found to be less severe. It has also been observed that there is a critical epilayer thickness (∼1 μm) below which the surface electron mobility is limited by dislocation scattering. reprint
 
13.  Intersubband hole absorption in GaAs-GaInP Quantum Wells grown by Gas Source Molecular Beam Epitaxy
J. Hoff, C. Jelen, S. Slivken, E. Michel, O. Duchemin, E. Bigan, and M. Razeghi with G. Brown and S.M. Hegde (Wright Laboratory)
Applied Physics Letters 65 (9)-- August 29, 1994
P-doped GaAs‐GaInP quantum wells have been grown on GaAs substrate by gas source molecular beam epitaxy. Structural quality has been evidenced by x-ray diffraction. A narrow low-temperature photoluminescence full width at half‐maximum has been measured. Strong hole intersubband absorption has been observed at 9 μm, and its dependence on light polarization has been investigated. reprint
 
14.  Efficiency of photoluminescence and excess carrier confinement in InGaAsP/GaAs structures prepared by metal-organic chemical vapor deposition
J. Diaz, H.J. Yi, M. Erdtmann, X. He, E. Kolev, D. Garbuzov, E. Bigan, and M. Razeghi
Journal of Applied Physics 76 (2)-- July 15, 1994
Special double‐ and separate‐confinement InGaAsP/GaAs heterostructures intended for photoluminescence measurements have been grown by low‐pressure metal‐organic chemical‐vapor deposition. The band gap of the active region quaternary material was close to 1.5 eV, and the waveguide of the separate‐confinement structures was near 1.8 eV. Measurement of the integrated luminescence efficiency at 300 K has shown that over a wide range of excitation level (10–103 W/cm²) radiative transitions are the dominant mechanism for excess carrier recombination in the active region of the structures studied. As determined by spectral measurements, the excess carrier concentration in the waveguide of the separate‐confinement heterostructures and the intensity of the waveguide emission band correspond to a condition of thermal equilibrium of the excess carrier populations in the active region and the waveguide. The ratio of the intensity of the waveguide emission to the active region emission fits a model which assumes that the barrier height for minority carriers (holes) is equal to the difference in band gaps between the active region and the waveguide region. reprint
 
15.  Thermal stability of GaN thin films grown on (0001) Al2O3, (0112) Al2O3 and (0001)Si 6H-SiC substrates
C.J. Sun, P. Kung, A. Saxler, H. Ohsato, E. Bigan, M. Razeghi, and D.K. Gaskill
Journal of Applied Physics 76 (1)-- July 1, 1994
Single crystals of GaN were grown on (0001), (0112) Al2O3 and (0001)Si 6H‐SiC substrates using an atmospheric pressure metalorganic chemical‐vapor‐deposition reactor. The relationship has been studied between the thermal stability of the GaN films and the substrate’s surface polarity. It appeared that the N‐terminated (0001) GaN surface grown on (0001)Si 6H‐SiC has the most stable surface, followed by the nonpolar (1120) GaN surface grown on (0112) Al2O3, while the Ga‐terminated (0001) GaN surface grown on (0001) Al2O3 has the least stable surface. This is explained with the difference in the atomic configuration of each of these surfaces which induces a difference in their thermal decomposition. reprint
 
16.  Characterization of InTlSb/InSb Grown by Low Pressure Metalorganic Chemical Vapor Deposition on GaAs Substrat
Y.H. Choi, P. Staveteig, E. Bigan, and M. Razeghi
Journal of Applied Physics 75 (6)-- March 15, 1994
Optical properties of InTlSb, a new long wavelength infrared material, are investigated. InTlSb/InSb epilayers grown by low‐pressure metal‐organic chemical vapor deposition on semi‐insulating GaAs substrates were characterized using Auger electron spectroscopy and Fourier transform infrared spectroscopy. Auger electron spectra confirm the presence of thallium. Transmission measurements at 77 K indicate an absorption shift from 5.5 μm for InSb up to 8 μm for InTlSb that is confirmed by photoconductivity measurements. reprint
 
17.  Photoconductance measurements on InTlSb/InSb/GaAs grown by low-pressure metalorganic chemical vapor deposition
P.T. Staveteig, Y.H. Choi, G. Labeyrie, E. Bigan, and M. Razeghi
Applied Physics Letters 64 (4)-- January 24, 1994
We report infrared photoconductors based on InTlSb/InSb grown by low‐pressure metalorganic chemical vapor deposition on semi-insulating GaAs substrates. The photoresponse spectrum extends up to 8 μm at 77 K. The absolute magnitude of the photoresponse is measured as a function of bias. The specific detectivity is estimated to be 3×108 Hz½·cm·W-1 at 7 μm wavelength. reprint
 
18.  InTlSb alloys for infrared detection
E. Bigan, Y.H. Choi, G. Labeyrie, and M. Razeghi
Proceedings, SPIE Nonlinear Optics for High-Speed Electronics and Optical Frequency Conversion, Vol. 2145-- January 24, 1994
InTISb alloys have been grown by low-pressure metalorganic chemical vapor deposition, and characterized. Photoconductors exhibit a cutoff wavelength that can be tailored from 5.5 μm up to 9 μm by varying the thallium content. Experimental observations suggest that this can be further extended by increasing the thallium content. An InTISb photoconductor having a 9 μm cutoff wavelength exhibited a D* of 109 cm·Hz½·W-1 at 7 μm operating wavelength. reprint
 
19.  High Quality Aluminum Nitride Epitaxial Layers Grown on Sapphire Substrates
A. Saxler, P. Kung, C.J. Sun, E. Bigan and M. Razeghi
Applied Physics Letters 64 (3)-- January 17, 1994
In this letter we report the growth of high quality AlN epitaxial layers on sapphire substrates. The AlN grown on (00·1) sapphire exhibited a better crystalline quality than that grown on (01·2) sapphire. An x-ray rocking curve of AlN on (00·1) Al2O3 yielded a full width at half-maximum of 97.2 arcsec, which is the narrowest value reported to our knowledge. The AlN peak on (01·2) Al2O3 was about 30 times wider. The absorption edge measured by ultraviolet transmission spectroscopy for AlN grown on (00·1) Al2O3 was about 197 nm. reprint
 
20.  The Effects of V/III Ratio on Optical, Electrical and Structural Properties of InAs0.3Sb0.7Grown by LP-MOCVD
Y.H. Choi, G. Labeyrie, P.T. Staveteig, E. Bigan, and M. Razeghi
Electrochemical Society Conference, New Orleans, LA; Proceedings, 94-5, Long Wavelength Infrared Detectors and Arrays: Physics and Applications, F. Radpour and V.R. McCrary (eds.)-- October 15, 1993
 
21.  In1- x TlxSb for Long-Wavelength Infrared Photodetectors
Y.H. Choi, P.T. Staveteig, E. Bigan, and M. Razeghi
Electrochemical Society Conference, New Orleans, LA; Proceedings, Vol. 94-5-- October 10, 1993
 
22.  High Quality InSb Epitaxial Film Grown by Low Pressure Metalorganic Chemical Vapor Deposition
Y.H. Choi, R. Sudharsanan, C. Besikci, E. Bigan, and M. Razeghi
Proceeding of Materials Research Society Conference Proceedings, Vol. 281-- November 1, 1992
 

Page 1  (22 Items)