Center for Quantum Devices - Journal Articles and Conference Proceedings

Page 4 of 32: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 >> Next (778 Items)

76.	High brightness ultraviolet light-emitting diodes grown on patterned silicon substrate Yoann Robin, Kai Ding, Ilkay Demir, Ryan McClintock, Sezai Elagoz, Manijeh Razeghi Materials Science in Semiconductor Processing 90, pp. 87–91-- November 5, 2018 We report on the fabrication of high brightness AlGaN-based ultraviolet light emitting diodes (UV-LED) on patterned silicon. Using the lateral epitaxial overgrowth approach, we demonstrate the growth of a 6 μm thick AlN layer of high crystalline quality. X-ray diffraction characterization showed a rocking curve with a full width at half maximum of 553 and 768″ for the (00.2) and (10.2) planes, respectively. The low dislocation density of the AlN template enabled the growth of bright AlGaN/ GaN quantum wells emitting at 336 nm. By appropriate flip-chip bonding and silicon substrate removal processing steps, the patterned AlN surface was exposed and efficient bottom-emission UV-LEDs were realized. Improvement of the AlN quality and the structure design allowed the optical output power to reach the milliwatt range under pulsed current, exceeding the previously reported maximum efficiency. Further investigations of the optical power at different pulsed currents and duty cycles show that thermal management in this device structure is still challenging, especially in continuous wave mode operation. The strategy presented here is of interest, since AlN crystalline quality improvement and optimization of the light extraction are the main issues inhibiting efficient UV emitter on silicon fabrication. reprint
77.	Single-mode, high-power, midinfrared, quantum cascade laser phased arrays Wenjia Zhou , Donghai Wu , Quan-Yong Lu, Steven Slivken & Manijeh Razeghi Scientific Reports 8:14866-- October 5, 2018 We demonstrate single-mode, 16-channel, optical phased arrays based on quantum cascade laser technology, with emission wavelengths around 4.8 μm. The integrated device consists of a distributed feedback seed section, a highly-efficient tree array multi-mode interferometer power splitter, and a 16-channel amplifier array with a 4° angled facet termination. With a single layer Y₂O₃ coating, the angled facet reflectivity is estimated to be less than 0.1% for suppressing amplifier self-lasing. A peak output power of 30 W is achieved with an emission spectrum narrower than 11 nm and a side mode suppression ratio over 25 dB. Far field distribution measurement result indicates a uniform phase distribution across the array output. Using the same phased array architecture, we also demonstrate single-mode 3.8 μm QCL amplifier arrays with up to 20 W output power. reprint
78.	Multiple-band, Single-mode, High-power, Phase-locked, Mid-infrared Quantum Cascade Laser Arrays Manijeh Razeghi, Wenjia Zhou, Quanyong Lu, Donghai Wu, and Steven Slivken Imaging and Applied Optics 2018, JTh1A.2-- September 15, 2018 Single-mode, 16-channel, phase-locked laser arrays based on quantum cascade laser technology are demonstrated at multiple spectral bands across the mid-infrared spectrum region. High peak output power of 50W is achieved around the long-wavelength band of 7.7µm, while a side mode suppression ratio over 25dB is obtained. Far field distribution measurement result indicates a uniform phase distribution across the array output. reprint
79.	Review of high power frequency comb sources based on InP From MIR to THZ at CQD Manijeh Razeghi, Quanyong Lu, Donghai Wu, Steven Slivken Event: SPIE Optical Engineering + Applications, 2018, San Diego, California, United States-- September 14, 2018 We present the recent development of high performance compact frequency comb sources based on mid-infrared quantum cascade lasers. Significant performance improvements of our frequency combs with respect to the continuous wave power output, spectral bandwidth, and beatnote linewidth are achieved by systematic optimization of the device's active region, group velocity dispersion, and waveguide design. To date, we have demonstrated the most efficient, high power frequency comb operation from a free-running room temperature continuous wave (RT CW) dispersion engineered QCL at λ~5-9 μm. In terms of bandwidth, the comb covered a broad spectral range of 120 cm⁻¹ with a radio-frequency intermode beatnote spectral linewidth of 40 Hz and a total power output of 880 mW at 8 μm and 1 W at ~5.0 μm. The developing characteristics show the potential for fast detection of various gas molecules. Furthermore, THz comb sources based on difference frequency generation in a mid-IR QCL combs could be potentially developed. reprint
80.	Terahertz emitters at Center for Quantum Devices: recent advances and future trends Manijeh Razeghi Proc. SPIE 10177, Infrared Technology and Applications XLIII, 1017705-- August 23, 2018 This paper reviews the recent advances and future trends of terahertz (THz) emitters at CQD/NU, highlights the high-performance THz sources based on intracavity nonlinear frequency generation in mid-infrared quantum cascade lasers. Significant performance improvements of our THz sources in the power, wall plug efficiency are achieved by systematic optimizing the device's active region, waveguide, and chip bonding strategy. High THz power up to 1.9 mW and 0.014 mW for pulsed mode and continuous wave operations at room temperature are demonstrated, respectively. Even higher power and efficiency are envisioned based on enhancements in outcoupling efficiency and mid-IR performance. Our compact THz device with high power and wide tuning range is highly suitable for the imaging, sensing, spectroscopy, medical diagnosis, and many other applications. reprint
81.	Demonstration of long wavelength infrared Type-II InAs/InAs_1-xSb_x superlattices photodiodes on GaSb substrate grown by metalorganic chemical vapor deposition D. H. Wu, A. Dehzangi, Y. Y. Zhang, M. Razeghi Applied Physics Letters 112, 241103-- June 12, 2018 We report the growth and characterization of long wavelength infrared type-II InAs/InAs_1−xSb_x superlattices photodiodes with a 50% cut-off wavelength at 8.0 μm on GaSb substrate grown by metalorganic chemical vapor deposition. At 77 K, the photodiodes exhibited a differential resistance at zero bias (R₀A) 8.0 Ω·cm², peak responsivity of 1.26 A/W corresponding to a quantum efficiency of 21%. A specific detectivity of 5.4×10¹⁰ cm·Hz^1/2/W was achieved at 7.5 μm. reprint
82.	Monolithic, steerable, mid-infrared laser realized with no moving parts Slivken S, Wu D, Razeghi M Scientific Reports 7, 8472 -- May 24, 2018 The mid-infrared (2.5 < λ < 25 μm) spectral region is utilized for many purposes, such as chemical/biological sensing, free space communications, and illuminators/countermeasures. Compared to near-infrared optical systems, however, mid-infrared component technology is still rather crude, with isolated components exhibiting limited functionality. In this manuscript, we make a significant leap forward in mid-infrared technology by developing a platform which can combine functions of multiple mid-infrared optical elements, including an integrated light source. In a single device, we demonstrate wide wavelength tuning (240 nm) and beam steering (17.9 degrees) in the mid-infrared with a significantly reduced beam divergence (down to 0.5 degrees). The architecture is also set up to be manufacturable and testable on a wafer scale, requiring no cleaved facets or special mirror coating to function. reprint
83.	Phase-locked, high power, mid-infrared quantum cascade laser array W. Zhou, S. Slivken, and M. Razeghi Applied Physics Letters 112, 181106-- May 4, 2018 We demonstrate phase-locked, high power quantum cascade laser arrays, which are combined using a monolithic, tree array multimode interferometer, with emission wavelengths around 4.8 μm. A maximum output power of 15 W was achieved from an eight-element laser array, which has only a slightly higher threshold current density and a similar slope efficiency compared to a Fabry-Perot laser of the same length. Calculated multimode interferometer splitting loss is on the order of 0.27 dB for the in-phase supermode. In-phase supermode operation with nearly ideal behavior is demonstrated over the working current range of the array. reprint
84.	Shortwave quantum cascade laser frequency comb for multi-heterodyne spectroscopy Q. Y. Lu, S. Manna, D. H. Wu, S. Slivken, and M. Razeghi Applied Physics Letters 112, 141104-- April 3, 2018 Quantum cascade lasers (QCLs) are versatile light sources with tailorable emitting wavelengths covering the mid-infrared and terahertz spectral ranges. When the dispersion is minimized, frequency combs can be directly emitted from quantum cascade lasers via four-wave mixing. To date, most of the mid-infrared quantum cascade laser combs are operational in a narrow wavelength range wherein the QCL dispersion is minimal. In this work, we address the issue of very high dispersion for shortwave QCLs and demonstrate 1-W dispersion compensated shortwave QCL frequency combs at λ~5.0 μm, spanning a spectral range of 100 cm⁻¹. The multi-heterodyne spectrum exhibits 95 equally spaced frequency comb lines, indicating that the shortwave QCL combs are ideal candidates for high-speed high-resolution spectroscopy reprint
85.	Thin-Film Antimonide-Based Photodetectors Integrated on Si Yiyun Zhang , Member, IEEE, Abbas Haddadi, Member, IEEE, Romain Chevallier, Arash Dehzangi, Member, IEEE, and Manijeh Razeghi , Life Fellow, IEEE IEEE JOURNAL OF QUANTUM ELECTRONICS, VOL. 54, NO. 2-- April 1, 2018 Monolithic integration of antimonide (Sb)-based compound semiconductors on Si is in high demand to enrich silicon photonics by extending the detection range to longer infrared wavelengths. In this paper, we have demonstrated the damage-free transfer of large-area (1×1 cm² ) narrow-bandgap Sb-based type-II superlattice (T2SL)-based thin-film materials onto a Si substrate using a combination of wafer-bonding and chemical epilayer release techniques. An array of Sb-based T2SL-based long-wavelength infrared (LWIR) photodetectors with diameters from 100 to 400 μm has been successfully fabricated using standard "top–down" processing technique. The transferred LWIR photodetectors exhibit a cut-off wavelength of λ 8.6 μm at 77 K. The dark current density of the transferred photodetectors under 200 mV applied bias at 77 K is as low as 5.7×10⁻⁴ A/cm² and the R×A reaches 66.3 Ω·cm², exhibiting no electrical degradation compared with reference samples on GaSb native substrate. The quantum efficiency and peak responsivity at 6.75 μm (@77 K, 200 mV) are 46.2% and 2.44 A/W, respectively. The specific detectivity (D^*) at 6.75 μm reaches as high as 1.6×10¹¹ cm·Hz^1/2/W under 200 mV bias at 77 K. Our method opens a reliable pathway to realize high performance and practical Sb-based optoelectronic devices on a Si platform. reprint
86.	The new oxide paradigm for solid state ultraviolet photodetectors D. J. Rogers, P. Bove, X. Arrateig, V. E. Sandana, F. H. Teherani, M. Razeghi, R. McClintock, E. Frisch, S. Harel, Proceedings Volume 10533, Oxide-based Materials and Devices IX; 105331P-- March 22, 2018 The bandgap of wurzite ZnO layers grown on 2 inch diameter c-Al₂O₃ substrates by pulsed laser deposition was engineered from 3.7 to 4.8 eV by alloying with Mg. Above this Mg content the layers transformed from single phase hcp to mixed hcp/fcc phase before becoming single phase fcc above a bandgap of about 5.5 eV. Metal-Semiconductor-Metal (MSM) photodetectors based on gold Inter-Digitated-Transducer structures were fabricated from the single phase hcp layers by single step negative photolithography and then packaged in TO5 cans. The devices gave over 6 orders of magnitude of separation between dark and light signal with solar rejection ratios (I270 : I350) of over 3 x 10⁵ and dark signals of 300 pA (at a bias of −5V). Spectral responsivities were engineered to fit the “Deutscher Verein des Gas- und Wasserfaches” industry standard form and gave over two decade higher responsivities (14 A/W, peaked at 270 nm) than commercial SiC based devices. Homogeneous Ga₂O₃ layers were also grown on 2 inch diameter c-Al₂O₃ substrates by PLD. Optical transmission spectra were coherent with a bandgap that increased from 4.9 to 5.4 eV when film thickness was decreased from 825 to 145 nm. X-ray diffraction revealed that the films were of the β-Ga₂O₃ (monoclinic) polytype with strong (−201) orientation. β-Ga₂O₃ MSM photodetectors gave over 4 orders of magnitude of separation between dark and light signal (at −5V bias) with dark currents of 250 pA and spectral responsivities of up to 40 A/W (at -0.75V bias). It was found that the spectral responsivity peak position could be decreased from 250 to 230 nm by reducing film thickness from 825 to 145 nm. This shift in peak responsivity wavelength with film thickness (a) was coherent with the apparent bandgap shift that was observed in transmission spectroscopy for the same layers and (b) conveniently provides a coverage of the spectral region in which MgZnO layers show fcc/hcp phase mixing. reprint
87.	Room temperature operation of In_xGa_1-xSb/InAs type-II quantum well infrared photodetectors grown by MOCVD D. H. Wu, Y. Y. Zhang, and M. Razeghi Applied Physics Letters 112, 111103-- March 14, 2018 We demonstrate room temperature operation of In_0.5Ga_0.5Sb/InAs type-II quantum well photodetectors on InAs substrate grown by metal-organic chemical vapor deposition. At 300 K, the detector exhibits a dark current density of 0.12 A/cm², peak responsivity of 0.72 A/W corresponding to a quantum efficiency of 23.3%, with calculated specific detectivity of 2.4×10⁹ cm.Hz^1/2/W at 3.81 μm. reprint
88.	A review of the growth, doping, and applications of β-Ga₂O₃ thin films Manijeh Razeghi, Ji-Hyeon Park , Ryan McClintock, Dimitris Pavlidis, Ferechteh H. Teherani, David J. Rogers, Brenden A. Magill, Giti A. Khodaparast, Yaobin Xu, Jinsong Wu, Vinayak P. Dravid Proc. SPIE 10533, Oxide-based Materials and Devices IX, 105330R -- March 14, 2018 β-Ga₂O₃ is emerging as an interesting wide band gap semiconductor for solar blind photo detectors (SBPD) and high power field effect transistors (FET) because of its outstanding material properties including an extremely wide bandgap (Eg ~4.9eV) and a high breakdown field (8 MV/cm). This review summarizes recent trends and progress in the growth/doping of β-Ga₂O₃ thin films and then offers an overview of the state-of-the-art in SBPD and FET devices. The present challenges for β-Ga₂O₃ devices to penetrate the market in real-world applications are also considered, along with paths for future work. reprint
89.	Sandwich method to grow high quality AlN by MOCVD Demir , H Li, Y Robin, R McClintock, S Elagoz and M Razeghi Journal of Physics D: Applied Physics 51, pp. 085104-- February 7, 2018 We report pulsed atomic layer epitaxy growth of a very high crystalline quality, thick (~2 µm) and crack-free AlN material on c-plane sapphire substrates via a sandwich method using metal organic chemical vapor deposition. This sandwich method involves the introduction of a relatively low temperature (1050 °C) 1500 nm thick AlN layer between two 250 nm thick AlN layers which are grown at higher temperature (1170 °C). The surface morphology and crystalline quality remarkably improve using this sandwich method. A 2 µm thick AlN layer was realized with 33 arcsec and 136 arcsec full width at half maximum values for symmetric and asymmetric reflections of ω-scan, respectively, and it has an atomic force microscopy root-mean-square surface roughness of ~0.71 nm for a 5 × 5 µm² surface area. reprint
90.	nBn extended short-wavelength infrared focal plane array ARASH DEHZANGI, ABBAS HADDADI, ROMAIN CHEVALLIER, YIYUN ZHANG, AND MANIJEH RAZEGHI Optics Letters Vol. 43, Issue 3, pp. 591-594-- February 1, 2018 An extended short-wavelength nBn InAs/GaSb/AlSb type-II superlattice-based infrared focal plane array imager was demonstrated. A newly developed InAs_0.10Sb_0.90∕GaSb superlattice design was used as the large-bandgap electron barrier in this photodetector. The large band gap electron-barrier design in this nBn photodetector architecture leads to the device having lower dark current densities. A new bi-layer etch-stop scheme using a combination of InAs_0.91Sb_0.09 bulk and AlAs_0.1Sb_0.9∕GaSb superlattice layers was introduced to allow complete substrate removal and a shorter wavelength cut-on. Test pixels exhibit 100% cutoff wavelengths of ∼2.30 and ∼2.48 μm at 150 and 300 K, respectively. The devices achieve saturated quantum efficiency values of 59.7% and 63.8% at 150 and 300 K, respectively, under backside illumination and without any antireflection coating.At 150 K, photodetectors exhibit dark current density of 8.75 × 10⁻⁸ A∕cm² under −400 mV applied bias, providing specific detectivity of 2.82 × 10¹² cm · Hz^1∕2∕W at 1.78 μm. At 300 K, the dark current density reaches 4.75 × 10⁻² A∕cm² under −200 mV bias, providing a specific detectivity of 8.55 × 10⁹ cm · Hz^1∕2∕W 1.78 μm. reprint
91.	Type-II InAs/GaSb/AlSb superlatticebased heterojunction phototransistors: back to the future Abbas Haddadi, Arash Dehzangi, Romain Chevallier, Thomas Yang, Manijeh Razeghi Proc. SPIE 10540, Quantum Sensing and Nano Electronics and Photonics XV- Page-1054004-1-- January 26, 2018 Most of reported HPTs in literatures are based on InGaAs compounds that cover NIR spectral region. However, InGaAs compounds provide limited cut-off wavelength tunability. In contrast, type-II superlattices (T2SLs) are a developing new material system with intrinsic advantages such as great flexibility in bandgap engineering, low growth and manufacturing cost, high-uniformity, auger recombination suppression, and high carrier effective mass that are becoming an attractive candidate for infrared detection and imaging from short-wavelength infrared to very long wavelength infrared regime. We present the recent advancements in T2SL-based heterojunction phototransistors in e– SWIR, MWIR and LWIR spectral ranges. A mid-wavelength infrared heterojunction phototransistor based on type-II InAs/AlSb/GaSb superlattices on GaSb substrate has been demonstrated. Then, we present the effect of vertical scaling on the optical and electrical performance of heterojunction phototransistors, where the performance of devices with different base width was compared as the base was scaled from 60 down to 40 nm. reprint
92.	Dark current reduction in microjunction-based compound electron barrier type-II InAs/InAs1-xSbx superlattice-based long-wavelength infrared photodetectors Romain Chevallier, Abbas Haddadi, Manijeh Razeghi Proc. SPIE 10540, Quantum Sensing and Nano Electronics and Photonics XV Page. 1054007-1-- January 26, 2018 Reduction of dark current density in microjunction-based InAs/InAs_1-xSb_x type-II superlattice long-wavelength infrared photodetectors was demonstrated. A double electron barrier design was used to suppress both generation-recombination and surface dark currents. The photodetectors exhibited high surface resistivity after passivation with SiO₂, which permits the use of small size features without having strong surface leakage current degrading the electrical performance. Fabricating a microjunction structure (25×25 μm² mesas with 10×10 μm² microjunctions) with this photodetector double barrier design results in a dark current density of 6.3×10^-6 A/cm² at 77 K. The device has an 8 μm cut-off wavelength at 77 K and exhibits a quantum efficiency of 31% for a 2 μm-thick absorption region, which results in a specific detectivity value of 1.2×10¹² cm·Hz^1/2/W at 77 K. reprint
93.	Broadband monolithically-tunable quantum cascade lasers Wenjia Zhou, Ryan McClintock, Donghai Wu, Steven Slivken, Manijeh Razeghi Proc. SPIE 10540, Quantum Sensing and Nano Electronics and Photonics XV, 105400A-- January 26, 2018 Mid-infrared lasers, emitting in the spectral region of 3-12 μm that contain strong characteristic vibrational transitions of many important molecules, are highly desirable for spectroscopy sensing applications. High efficiency quantum cascade lasers have been demonstrated with up to watt-level output power in the mid-infrared region. However, the wide wavelength tuning, which is critical for spectroscopy applications, is still largely relying on incorporating external gratings, which have stability issues. Here, we demonstrate the development a monolithic, widely tunable quantum cascade laser source emitting between 6.1 and 9.2 μm through an on-chip integration of a sampled grating distributed feedback tunable laser array with a beam combiner. A compact tunable laser system was built to drive the individual lasers within the array and coordinate the driving of the laser array to produce desired wavelength. A broadband spectral measurement (520cm^-1) of methane shows excellent agreement with Fourier transform infrared spectrometer measurement. Further optimizations have led to high performance monolithic tunable QCLs with up to 65 mW output while delivering fundamental mode outputs. reprint
94.	Recent progress of widely tunable, CW THz sources based QCLs at room temperature Manijeh Razeghi Terahertz Science and Technology, Vol.10, No.4, pp. 87-151-- December 7, 2017 The THz spectral region is of significant interest to the scientific community, but is one of the hardest regions to access with conventional technology. A wide range of compelling new applications are initiating a new revolution in THz technology, especially with regard to the development of compact and versatile devices for THz emission and detection. In this article, recent advances with regard to III-V semiconductor optoelectronics are explored with emphasis on how these advances will lead to the next generation of THz component technology reprint
95.	Progress in monolithic, broadband, widely tunable midinfrared quantum cascade lasers Manijeh Razeghi Wenjia Zhou Ryan McClintock Donghai Wu Steven Slivken Optical Engineering 57(1), 011018-- December 1, 2017 We present recent progress on the development of monolithic, broadband, widely tunable midinfrared quantum cascade lasers. First, we show a broadband midinfrared laser gain realized by a heterogeneous quantum cascade laser based on a strain balanced composite well design of Al_0.63In_0.37As∕Ga_0.35In_0.65As∕ Ga_0.47In_0.53As. Single mode emission between 5.9 and 10.9 μm under pulsed mode operation was realized from a distributed feedback laser array, which exhibited a flat current threshold across the spectral range. Using the broadband wafer, a monolithic tuning between 6.2 and 9.1 μm was demonstrated from a beam combined sampled grating distributed feedback laser array. The tunable laser was utilized for a fast sensing of methane under pulsed operation. Transmission spectra were obtained without any moving parts, which showed excellent agreement to a standard measurement made by a Fourier transform infrared spectrometer. reprint
96.	A lifetime of contributions to the world of semiconductors using the Czochralski invention Manijeh Razeghi Journal of Vacuum Volume 146, Pages 308-328-- December 1, 2017 Over the course of my career, I have made numerous contributions related to semiconductor crystal growth and high performance optoelectronics over a vast region of the electromagnetic spectrum (ultraviolet to terahertz). In 2016 this cumulated in my receiving the Jan Czochralski Gold Medal award from the European Materials Research Society. This article is designed to provide a historical perspective and general overview of these scientific achievements, on the occasion of being honored by this award. These achievements would not have been possible without high quality crystalline substrates, and this article is written in honor of Jan Czochralski on the 100th anniversary of his important discovery. reprint
97.	Type-II superlattice-based extended short-wavelength infrared focal plane array with an AlAsSb/GaSb superlattice etch-stop layer to allow near-visible light detection Romain Chevallier, Arash Dehzangi, Abbas Haddadi, and Manijeh Razeghi Optics Letters Vol. 42, Iss. 21, pp. 4299-4302-- October 17, 2017 A versatile infrared imager capable of imaging the near-visible to the extended short-wavelength infrared (e-SWIR) is demonstrated using e-SWIR InAs/GaSb/AlSb type-II superlattice-based photodiodes. A bi-layer etch-stop scheme consisting of bulk InAs_0.91Sb_0.09 and AlAs_0.1Sb_0.9/GaSb superlattice layers is introduced for substrate removal from the hybridized back-side illuminated photodetectors. The implementation of this new technique on an e-SWIR focal plane array results in a significant enhancement in the external quantum efficiency (QE) in the 1.8–0.8μm spectral region, while maintaining a high QE at wavelengths longer than 1.8μm. Test pixels exhibit 100% cutoff wavelengths of ∼2.1 and ∼2.25μm at 150 and 300K, respectively. They achieve saturated QE values of 56% and 68% at 150 and 300K, respectively, under back-side illumination and without any anti-reflection coating. At 150K, the photodetectors (27μm×27μm area) exhibit a dark current density of 4.7×10⁻⁷ A/cm² under a −50 mV applied bias providing a specific detectivity of 1.77×10¹² cm·Hz^1/2/W. At 300K, the dark current density reaches 6.6×10⁻² A/cm² under −50 mV bias, providing a specific detectivity of 5.17×10⁹ cm·Hz^1/2/W. reprint
98.	Bias-selectable three-color short-, extended-short-, and mid-wavelength infrared photodetectors based on type-II InAs/GaSb/AlSb superlattices Abbas Haddadi, and Manijeh Razeghi Optics Letters Vol. 42, Iss. 21, pp. 4275-4278-- October 16, 2017 A bias-selectable, high operating temperature, three-color short-, extended-short-, and mid-wavelength infrared photodetector based on InAs/GaSb/AlSb type-II superlattices on GaSb substrate has been demonstrated. The short-, extended-short-, and mid-wavelength channels’ 50% cutoff wavelengths were 2.3, 2.9, and 4.4μm, respectively, at 150K. The mid-wavelength channel exhibited a saturated quantum efficiency of 34% at 4μm under +200 mV bias voltage in a front-side illumination configuration and without any antireflection coating. At 200mV, the device exhibited a dark current density of 8.7×10⁻⁵ A/cm² providing a specific detectivity of ∼2×10¹¹ cm·Hz^1/2/W at 150K. The short-wavelength channel achieved a saturated quantum efficiency of 20% at 1.8μm. At −10 mV, the device’s dark current density was 5.5×10⁻⁸ A/cm². At zero bias, its specific detectivity was 1×10¹¹ cm·Hz^1/2/W at 150K. The extended short-wavelength channel achieved a saturated quantum efficiency of 22% at 2.75 μm. Under −2 V bias voltage, the device exhibited a dark current density of 1.8×10⁻⁶ A/cm² providing a specific detectivity of 6.3×10¹¹ cm·Hz^1/2/W at 150K. reprint
99.	Recent progress of quantum cascade laser research from 3 to 12 μm at the Center for Quantum Devices MANIJEH RAZEGHI,* WENJIA ZHOU,STEVEN SLIVKEN,QUAN-YONG LU,DONGHAI WU, AND RYAN MCCLINTOC Applied Optics Vol. 56, No. 31 -- October 10, 2017 The quantum cascade laser (QCL) is becoming the leading laser source in the mid-infrared (mid-IR) range, which contains two atmospheric transmission windows and many molecular fingerprint absorption features. Since its first demonstration in 1994, the QCL has undergone tremendous development in terms of the output power, wall plug efficiency, wavelength coverage, tunability and beam quality. At the Center for Quantum Devices, we have demonstrated high-power continuous wave operation of QCLs covering a wide wavelength range from 3 to 12 μm, with power output up to 5.1 W at room temperature. Recent research has resulted in power scaling in pulsed mode with up to 203 W output, electrically tunable QCLs based on monolithic sampled grating design, heterogeneous QCLs with a broad spectral gain, broadly tunable on-chip beam-combined QCLs, QCL-based mid-IR frequency combs, and fundamental mode surface emitting quantum cascade ring lasers. The developed QCLs will be the basis for a number of next-generation spectroscopy and sensing systems. reprint
100.	Dark current reduction in microjunction-based double electron barrier type-II InAs/InAsSb superlattice long-wavelength infrared photodetectors Romain Chevallier, Abbas Haddadi, & Manijeh Razeghi Scientific Reports 7, Article number: 12617-- October 3, 2017 Microjunction InAs/InAsSb type-II superlattice-based long-wavelength infrared photodetectors with reduced dark current density were demonstrated. A double electron barrier design was employed to reduce both bulk and surface dark currents. The photodetectors exhibited low surface leakage after passivation with SiO2, allowing the use of very small size features without degradation of the dark current. Fabricating microjunction photodetectors (25 × 25 µm² diodes with 10 × 10 µm² microjunctions) in combination with the double electron barrier design results in a dark current density of 6.3 × 10⁻⁶ A/cm² at 77 K. The device has an 8 µm cut-off wavelength at 77 K and exhibits a quantum efficiency of 31% for a 2 µm-thick absorption region, which results in a specific detectivity value of 1.2 × 10¹² cm·Hz^½/W. reprint

Page 4 of 32: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 >> Next (778 Items)