Center for Quantum Devices - Journal Articles and Conference Proceedings

Page 3 of 3: Prev << 1 2 3 (73 Items)

51.	Dark current suppression in Type-II InAs/GaSb superlattice long wavelength infrared photodiodes with M-structure barrier B.M. Nguyen, D. Hoffman, P.Y. Delaunay, and M. Razeghi Applied Physics Letters, Vol. 91, No. 16, p. 163511-1-- October 15, 2007 We presented an alternative design of Type-II superlattice photodiodes with the insertion of a mid-wavelength infrared M-structure AlSb/GaSb/InAs/GaSb/AlSb superlattice for the reduction of dark current. The M-structure superlattice has a larger carrier effective mass and a greater band discontinuity as compared to the standard Type-II superlattices at the valence band. It acts as an effective medium that weakens the diffusion and tunneling transport at the depletion region. As a result, a 10.5 µm cutoff Type-II superlattice with 500 nm M-superlattice barrier exhibited a R₀A of 200 cm² at 77 K, approximately one order of magnitude higher than the design without the barrier. The quantum efficiency of such structures does not show dependence on either barrier thickness or applied bias. reprint
52.	Beryllium compensation doping of InAs/GaSb infrared superlattice photodiodes D. Hoffman, B.M. Nguyen, P.Y. Delaunay, A. Hood, M. Razeghi and J. Pellegrino Applied Physics Letters, Vol. 91, No. 14, p. 143507-1-- October 1, 2007 Capacitance-voltage measurements in conjunction with dark current measurements on InAs/GaSb long wavelength infrared superlattice photodiodes grown by molecular-beam epitaxy on GaSb substrates are reported. By varying the beryllium concentration in the InAs layer of the active region, the residually n-type superlattice is compensated to become slightly p-type. By adjusting the doping, the dominant dark current mechanism can be varied from diffusion to Zener tunneling. Minimization of the dark current leads to an increase of the zero-bias differential resistance from less than 4 to 32 cm² for a 100% cutoff of 12.05 µm reprint
53.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, S.R. Darvish, S. Slivken, P. Sung, J. Nguyen, A. Evans, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 91, No. 14, p. 141123-1-- October 1, 2007 We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~4.75 µm. Ridge waveguides of 100 µm width were fabricated with both PCDFB and Fabry-Pérot feedback mechanisms. The Fabry-Pérot device has a broad emitting spectrum and a double lobed far-field character. The PCDFB device, as expected, has primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half maximum of 2.4°. This accomplishment represents the first step in power scaling of single mode, midinfrared laser diodes operating at room temperature. reprint
54.	Polarity inversion of Type-II InAs/GaSb superlattice photodiodes B.M. Nguyen, D. Hoffman, P.Y. Delaunay, M. Razeghi and V. Nathan Applied Physics Letters, Vol. 91, No. 10, p. 103503-1-- September 3, 2007 The authors demonstrated the realization of p-on-n Type-II InAs/GaSb superlattice photodiodes. Growth condition for high quality InAsSb layer lattice matched to GaSb was established for the use of an effective n-contact layer. By studying the effect of various GaSb capping layer thicknesses on the optical and electrical performances, an optimized thickness of 160 nm was determined. In comparison to as grown n-on-p superlattice photodiodes, this inverted design of p on n has shown similar quality. Finally, by analyzing Fabry-Perot interference fringes in the front side illuminated spectral measurement, the refractive index of the superlattice was determined to be approximately 3.8. reprint
55.	Passivation of type-II InAs/GaSb double heterostructure P.Y. Delaunay, A. Hood, B.M. Nguyen, D. Hoffman, Y. Wei, and M. Razeghi Applied Physics Letters, Vol. 91, No. 9, p. 091112-1-- August 27, 2007 Focal plane array fabrication requires a well passivated material that is resistant to aggressive processes. The authors report on the ability of type-II InAs/GaSb superlattice heterodiodes to be more resilient than homojunctions diodes in improving sidewall resistivity through the use of various passivation techniques. The heterostructure consisting of two wide band gap (5 µm) superlattice contacts and a low band gap active region (11 µm) exhibits an R₀A averaging of 13·Ω cm². The devices passivated with SiO₂, Na₂S and SiO₂ or polyimide did not degrade compared to the unpassivated sample and the resistivity of the sidewalls increased to 47 kΩ·cm. reprint
56.	Buried heterostructure quantum cascade lasers with high continuous-wave wall plug efficiency A. Evans, S.R. Darvish, S. Slivken, J. Nguyen, Y. Bai and M. Razeghi Applied Physics Letters, Vol. 91, No. 7, p. 071101-1-- August 13, 2007 The authors report on the development of ~4.7 µm strain-balanced InP-based quantum cascade lasers with high wall plug efficiency and room temperature continuous-wave operation. The use of narrow-ridge buried heterostructure waveguides and thermally optimized packaging is presented. Over 9.3% wall plug efficiency is reported at room temperature from a single device producing over 0.675 W of continuous-wave output power. Wall plug efficiencies greater than 18% are also reported for devices at a temperature of 150 K, with continuous-wave output powers of more than 1 W. reprint
57.	High-power mid- and far- wavelength infrared lasers for free space communication M. Razeghi; A. Evans; J. Nguyen; Y. Bai; S. Slivken; S.R. Darvish; K. Mi Proc. SPIE 6593, Photonic Materials, Devices, and Applications II, 65931V (June 12, 2007)-- June 12, 2007 Laser-based free-space communications have been developed to serve specific roles in "last mile" high-speed data networks due to their high security, low cost, portability, and high bandwidth. Conventional free-space systems based on near infrared optical devices suffer from reliability problems due to atmospheric scattering losses and scintillation effects, such as those encountered with storms, dust, and fog. Mid-infrared wavelengths are less affected by atmospheric effects and can significantly enhance link up-time and range. This paper will discuss some of the recent advances in high-power, high temperature, high reliability mid-infrared Quantum Cascade Lasers and their potential application in highly reliable free space communication links. reprint
58.	Very high quantum efficiency in type-II InAs/GaSb superlattice photodiode with cutoff of 12 µm B.M. Nguyen, D. Hoffman, Y. Wei, P.Y. Delaunay, A. Hood and M. Razeghi Applied Physics Letters, Vol. 90, No. 23, p. 231108-1-- June 4, 2007 The authors report the dependence of the quantum efficiency on device thickness of Type-II InAs/GaSb superlattice photodetectors with a cutoff wavelength around 12 µm. The quantum efficiency and responsivity show a clear delineation in comparison to the device thickness. An external single-pass quantum efficiency of 54% is obtained for a 12 µm cutoff wavelength photodiodes with a -region thickness of 6.0 µm. The R₀A value is kept stable for the range of structure thicknesses allowing for a specific detectivity (2.2×10¹¹ cm·Hz^½/W). reprint
59.	Near bulk-limited R0A of long-wavelength infrared type-II InAs/GaSb superlattice photodiodes with polyimide surface passivation Andrew Hood, Pierre-Yves Delaunay, Darin Hoffman, Binh-Minh Nguyen, Yajun Wei, Manijeh Razeghi, and Vaidya Nathan Applied Physics Letters 90, 233513-- June 4, 2007 Effective surface passivation of Type-II InAs/GaSb superlattice photodiodes with cutoff wavelengths in the long-wavelength infrared is presented. A stable passivation layer, the electrical properties of which do not change as a function of the ambient environment nor time, has been prepared by a solvent-based surface preparation, vacuum desorption, and the application of an insulating polyimide layer. Passivated photodiodes, with dimensions ranging from 400×400 to 25×25 µm², with a cutoff wavelength of ~11 µm, exhibited near bulk-limited R₀A values of ~12 Ω·cm², surface resistivities in excess of 10⁴ Ω·cm, and very uniform current-voltage behavior at 77 K. reprint
60.	Current status of high performance quantum cascade lasers at the center for quantum devices M. Razeghi; A. Evans; Y. Bai; J. Nguyen; S. Slivken; S.R. Darvish; K. Mi Conference Proceedings - International Conference on Indium Phosphide and Related Materials. 588-593:[4266015] (2007)-- May 14, 2007 Mid-infrared laser sources are highly desired for laser-based trace chemical sensors, military countermeasures, free-space communications, as well as developing medical applications. While application development has been limited by the availability of adequate mid-infrared sources, InP-based quantum cascade lasers (QCLs) hold promise as inexpensive, miniature, portable solutions capable of producing high powers and operating at high temperatures with excellent beam quality and superior reliability. This paper discusses the most recent developments of application-ready high power (> 100 mW), continuous-wave (CW), mid-infrared QCLs operating above room temperature with lifetimes exceeding 13,000 hours. reprint
61.	320x256 infrared focal plane array based on type-II InAs/GaSb superlattice with a 12 μm cutoff wavelength P.Y. Delaunay, B.M. Nguyen, D. Hoffman, and M. Razeghi SPIE Porceedings, Vol. 6542, Orlando, FL 2007, p. 654204-- April 9, 2007 In the past few years, significant progress has been made in the structure design, growth and processing of Type-II InAs/GaSb superlattice photodetectors. Type-II superlattice demonstrated its ability to perform imaging in the middle and long infra-red range, becoming a potential competitor for technologies such as QWIP and HgCdTe. Using an empirical tight-binding model, we developed a superlattice design that matches the lattice parameter of GaSb substrates and presents a cutoff wavelength of 12 μm. Electrical and optical measurements performed on single element detectors at 77 K showed an R₀A averaging 13 Ω·cm² and a quantum efficiency as high as 54%. We demonstrated high quality material growth with x-ray FWHM below 30 arcsec and an AFM rms roughness of 1.5 Å over an area of 20x20 μm². A 320x256 array of 25x25μm² pixels, hybridized to an Indigo Read Out Integrated Circuit, performed thermal imaging up to 185 K with an operability close to 97%. The noise equivalent temperature difference at 81 K presented a peak at 270 mK, corresponding to a mean value of 340 mK. reprint
62.	Techniques for High-Quality SiO₂ Films J. Nguyen and M. Razeghi SPIE Conference, January 25-29, 2007, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices IV, Vol. 6479, p. 64791K-1-8-- January 29, 2007 We report on the comparison of optical, structural, and electrical properties of SiO₂ using plasma-enhanced chemical vapor deposition and ion-beam sputtering deposition. High-quality, low-temperature deposition of SiO₂ by ion-beam sputtering deposition is shown to have lower absorption, smoother and more densely packed films, a lower amount of fixed oxide charges, and a lower trapped-interface density than SiO₂ by plasma-enhanced chemical vapor deposition. This high-quality SiO₂ is then demonstrated as an excellent electrical and mechanical surface passivation layer on Type-II InAs/GaSb photodetectors reprint
63.	Type-II ‘M’ Structure Photodiodes: An Alternative Material Design for Mid-Wave to Long Wavelength Infrared Regimes B-M. Nguyen, M. Razeghi, V. Nathan, and G.J. Brown SPIE Conference, January 25-29, 2007, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices IV, Vol. 6479, p. 64790S-1-10-- January 29, 2007 In this work, an AlSb-containing Type-II InAs/GaSb superlattice, the so-called M-structure, is presented as a candidate for mid and long wavelength infrared detection devices. The effect of inserting an AlSb barrier in the GaSb layer is discussed and predicts many promising properties relevant to practical use. A good agreement between the theoretical calculation based on Empirical Tight Binding Method framework and experimental results is observed, showing the feasibility of the structure and its properties. A band gap engineering method without material stress constraint is proposed. reprint
64.	Influence of Residual Impurity Background on the Non-radiative Recombination Processes in High Purity InAs/GaSb superlattice Photodiodes E.C.F. da Silva, D. Hoffman, A. Hood, B. Nguyen, P.Y. Delaunay and M. Razeghi Applied Physics Letters, 89 (24)-- December 11, 2006 The influence of the impurity background on the recombination processes in type-II InAs/GaSb superlattice photodiodes with a cutoff wavelength of approximately 4.8 μm was investigated by electroluminescence measurements. Using an iterative fitting procedure based on the dependence of the quantum efficiency of the electroluminescence on the injection current, the Auger and Shockley-Read-Hall lifetimes were determined reprint
65.	First Demonstration of ~ 10 microns FPAs in InAs/GaSb SLS M. Razeghi, P.Y. Delaunay, B.M. Nguyen, A. Hood, D. Hoffman, R. McClintock, Y. Wei, E. Michel, V. Nathan and M. Tidrow IEEE LEOS Newsletter 20 (5)-- October 1, 2006 The concept of Type-II InAs/GaSb superlattice was first brought by Nobel Laureate L. Esaki, et al. in the 1970s. There had been few studies on this material system until two decades later when reasonable quality material growth was made possible using molecular beam epitaxy. With the addition of cracker cells for the group V sources and optimizations of material growth conditions, the superlattice quality become significantly improved and the detectors made of these superlattice materials can meet the demand in some practical field applications. Especially in the LWIR regime, it provides a very promising alternative to HgCdTe for better material stability and uniformity, etc. We have developed the empirical tight binding model (ETBM) for precise determination of the superlattice bandgap. reprint
66.	Optical Coatings by ion-beam sputtering deposition for long-wave infrared quantum cascade lasers J. Nguyen, J.S. Yu, A. Evans, S. Slivken and M. Razeghi Applied Physics Letters, 89 (11)-- September 11, 2006 The authors report on the development of high-reflection and multilayer antireflection coatings using ion-beam sputtering deposition for long-wave infrared (λ~9.4 μm) quantum cascade lasers. A metallic high-reflection coating structure using Y₂O₃ and Au is demonstrated to achieve a high reflectance of 96.70%, and the use of a multilayer anti-reflection coating structure using PbTe and ZnO is demonstrated to achieve a very low reflectance of 1.64%. reprint
67.	High differential resistance type-II InAs/GaSb superlattice photodiodes for the long-wavelength infrared A. Hood, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E. Michel and M. Razeghi Applied Physics Letters, 89 (9)-- August 28, 2006 Type-II InAs/GaSb superlattice photodiodes with a 50% cutoff wavelength ranging from 11 to 13 μm are presented. Optimization of diffusion limited photodiodes provided superlattice structures for improved injection efficiency in direct injection hybrid focal plane array applications. reprint
68.	Type-II superlattice photodetectors for MWIR to VLWIR focal plane arrays M. Razeghi, Y. Wei, A. Hood, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E. Michel and R. McClintock SPIE Infrared Technology and Applications Conference, April 17-21, 2006, Orlando, FL Proceedings – Infrared Technology and Applications XXXII, Vol. 6206, p. 62060N-1-- April 21, 2006 Results obtained on GaSb/InAs Type-II superlattices have shown performance comparable to HgCdTe detectors, with the promise of higher performance due to reduced Auger recombination and dark current through improvements in device design and material quality. In this paper, we discuss advancements in Type-II IR sensors that cover the 3 to > 30 µm wavelength range. Specific topics covered will be device design and modeling using the Empirical Tight Binding Method (ETBM), material growth and characterization, device fabrication and testing, as well as focal plane array processing and imaging. Imaging has been demonstrated at room temperature for the first time with a 5 µm cutoff wavelength 256×256 focal plane array. reprint
69.	High-power λ ~ 9.5 µm quantum-cascade lasers operating above room temperature in continuous-wave mode J.S. Yu, S. Slivken, A. Evans, S.R. Darvish, J. Nguyen, and M. Razeghi Applied Physics Letters, 88 (9)-- February 27, 2006 We report high-power continuous-wave (cw) operation of λ~9.5 μm quantum-cascade lasers to a temperature of 318 K. A high-reflectivity-coated 19-μm-wide and 3-mm-long device exhibits cw output powers as high as 150 mW at 288 K and still 22 mW at 318 K. In cw operation at 298 K, a threshold current density of 1.57 kA/cm², a slope efficiency of 391 mW/A, and a maximum wall-plug efficiency of 0.71% are obtained. reprint
70.	Quantum-Cascade Lasers Operating in Continuous-Wave Mode Above 90°C at λ ~5.25 µm A. Evans, J. Nguyen, S. Slivken, J.S. Yu, S.R. Darvish, and M. Razeghi Applied Physics Letters 88 (5)-- January 30, 2006 We report on the design and fabrication of λ~5.25 μm quantum-cascade lasers (QCLs) for very high temperature continuous-wave (CW) operation. CW operation is reported up to a maximum temperature of 90 °C (363 K). CW output power is reported in excess of 500 mW near room temperature with a low threshold current density. A finite element thermal model is used to investigate the G_th and maximum CW operating temperature of the QCLs. reprint
71.	Room-temperature continuous-wave operation of quantum-cascade lasers at λ ~ 4 µm J.S. Yu, S.R. Darvish, A. Evans, J. Nguyen, S. Slivken, and M. Razeghi Applied Physics Letters 88 (4)-- January 23, 2006 High-power cw λ~4 μm quantum-cascade lasers (QCLs) are demonstrated. The effect of different cavity length and laser die bonding is also investigated. For a high-reflectivity-coated 11-μm-wide and 4-mm-long epilayer-down bonded QCL, cw output powers as high as 1.6 W at 80 K and 160 mW at 298 K are obtained, and the cw operation is achieved up to 313 K with 12 mW. reprint
72.	High-Power Distributed-Feedback Quantum Cascade Lasers W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A.J. Evans, J.S. Yu, S.R. Darvish, S. Slivken and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 612704-- January 23, 2006 Recently, a distributed-feedback quantum cascade laser operating in a single spectral mode at 4.8 µm and at temperatures up to 333 K has been reported. In the present work, we provide detailed measurements and modeling of its performance characteristics. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single-mode at all currents and temperatures tested. Cw output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. reprint
73.	Characterization and Analysis of Single-Mode High-Power CW Quantum-Cascade Laser W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A. Evans, J.S. Yu, S.R. Darvish, S. Slivken, and M. Razeghi Journal of Applied Physics 98-- October 15, 2005 We measured and modeled the performance characteristics of a distributed-feedback quantum-cascade laser exhibiting high-power continuous-wave (CW) operation in a single spectral mode at λ~4.8 µm and temperatures up to 333 K. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single mode at all currents and temperatures tested. CW output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. The slope efficiency and subthreshold amplified spontaneous emission spectra are shown to be consistent with a coupling coefficient of no more than κL ~ 4–5, which is substantially lower than the estimate of 9 based on the nominal grating fabrication parameters. reprint

Page 3 of 3: Prev << 1 2 3 (73 Items)