Center for Quantum Devices - Journal Articles and Conference Proceedings

Page 2 of 3: Prev << 1 2 3 >> Next (73 Items)

26.	Minority electron unipolar photodetectors based on Type-II InAs/GaSb/AlSb superlattices for very long wavelength infrared detection B.M. Nguyen, S. Bogdanov, S. Abdollahi Pour, and M. Razeghi Applied Physics Letters, Vol. 95, No. 18, p. 183502-- November 2, 2009 We present a hybrid photodetector design that inherits the advantages of traditional photoconductive and photovoltaic devices. The structure consists of a barrier layer blocking the transport of majority holes in a p-type semiconductor, resulting in an electrical transport due to minority carriers with low current density. By using the M-structure superlattice as a barrier region, the band alignments can be experimentally controlled, allowing for the efficient extraction of the photosignal with less than 50 mV bias. At 77 K, a 14 µm cutoff detector exhibits a dark current 3.3 mA·cm⁻², a photoresponsivity of 1.4 A/W, and the associated shot noise detectivity of 4×10¹⁰ Jones. reprint
27.	Demonstration of high performance long wavelength infrared Type-II InAs/GaSb superlattice photodidoe grown on GaAs substrate S. Abdollahi Pour, B.M. Nguyen, S. Bogdanov, E.K. Huang, and M. Razeghi Applied Physics Letters, Vol. 95, No. 17, p. 173505-- October 26, 2009 We report the growth and characterization of long wavelength infrared type-II InAs/GaSb superlattice photodiodes with a 50% cut-off wavelength at 11 µm, on GaAs substrate. Despite a 7.3% lattice mismatch to the substrate, photodiodes passivated with polyimide exhibit an R₀A value of 35 Ω·cm² at 77 K, which is in the same order of magnitude as reference devices grown on native GaSb substrate. With a reverse applied bias less than 500 mV, the dark current density and differential resistance-area product are close to that of devices on GaSb substrate, within the tolerance of the processing and measurement. The quantum efficiency attains the expected value of 20% at zero bias, resulting in a Johnson limited detectivity of 1.1×10¹¹ Jones. Although some difference in performances is observed, devices grown on GaAs substrate already attained the background limit performance at 77 K with a 300 K background and a 2-π field of view. reprint
28.	Tunability of intersubband absorption from 4.5 to 5.3 µm in a GaN/Al_0.2Ga_0.8N superlattices grown by metalorganic chemical vapor deposition N. Péré-Laperne, C. Bayram, L. Nguyen-Thê, R. McClintock, and M. Razeghi Applied Physics Letters, Vol. 95, No. 13, p. 131109-- September 28, 2009 Intersubband (ISB) absorption at wavelengths as long as 5.3 µm is realized in GaN/Al_0.2Ga_0.8N superlattices grown by metalorganic chemical vapor deposition. By employing low aluminum content Al_0.2Ga_0.8N barriers and varying the well width from 2.6 to 5.1 nm, ISB absorption has been tuned from 4.5 to 5.3 µm. Theoretical ISB absorption and interband emission models are developed and compared to the experimental results. The effects of band offsets and the piezoelectric fields on these superlattices are investigated. reprint
29.	State-of-the-art Type II Antimonide-based superlattice photodiodes for infrared detection and imaging M. Razeghi, B.M. Nguyen, P.Y. Delaunay, E.K. Huang, S. Abdollahi Pour, P. Manurkar, and S. Bogdanov SPIE Proceedings, Nanophotonics and Macrophotonics for Space Environments II, San Diego, CA, Vol. 7467, p. 74670T-1-- August 5, 2009 Type-II InAs/GaSb Superlattice (SL), a system of multi interacting quantum wells was first introduced by Nobel Laureate L. Esaki in the 1970s. Since then, this low dimensional system has drawn a lot of attention for its attractive quantum mechanics properties and its grand potential for the emergence into the application world, especially in infrared detection. In recent years, Type-II InAs/GaSb superlattice photo-detectors have experienced significant improvements in material quality, structural designs and imaging applications which elevated the performances of Type-II InAs/GaSb superlattice photodetectors to a comparable level to the state-of-the-art Mercury Cadmium Telluride. We will present in this talk the current status of the state-of-the-art Type II superlattice photodetectors and focal plane arrays, and the future outlook for this material system. reprint
30.	Demonstration of mid-infrared type-II InAs/GaSb superlattice photodiodes grown on GaAs substrate B.M. Nguyen, D. Hoffman, E.K. Huang, S. Bogdanov, P.Y. Delaunay, M. Razeghi and M.Z. Tidrow Applied Physics Letters, Vol. 94, No. 22-- June 8, 2009 We report the growth and characterization of type-II InAs/GaSb superlattice photodiodes grown on a GaAs substrate. Through a low nucleation temperature and a reduced growth rate, a smooth GaSb surface was obtained on the GaAs substrate with clear atomic steps and low roughness morphology. On the top of the GaSb buffer, a p⁺-i-n⁺ type-II InAs/GaSb superlattice photodiode was grown with a designed cutoff wavelength of 4 μm. The detector exhibited a differential resistance at zero bias (R₀A)in excess of 1600 Ω·cm² and a quantum efficiency of 36.4% at 77 K, providing a specific detectivity of 6 X 10¹¹ cm·Hz^½/W and a background limited operating temperature of 100 K with a 300 K background. Uncooled detectors showed similar performance to those grown on GaSb substrates with a carrier lifetime of 110 ns and a detectivity of 6 X 10⁸ cm·Hz^½/W. reprint
31.	Recent Advances in LWIR Type-II InAs/GaSb Superlattice Photodetectors and Focal Plane Arrays at the Center for Quantum Devices M. Razeghi, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E.K. Huang, M.Z. Tidrow, and V. Nathan IEEE Proceedings, Vol. 97, No. 6, p. 1056-1066-- June 1, 2009 In recent years, Type-II InAs/GaSb superlattice photo-detectors have experienced significant improvements in material quality, structural designs, and imaging applications. They now appear to be a possible alternative to the state-of-the-art HgCdTe (MCT) technology in the long and very long wavelength infrared regimes. At the Center for Quantum Devices, we have successfully realized very high quantum efficiency, very high dynamic differential resistance R₀A - product LWIR Type – II InAs/GaSb superlattice photodiodes with efficient surface passivation techniques. The demonstration of high quality LWIR Focal Plane Arrays that were 100 % fabricated in - house reaffirms the pioneer position of this university-based laboratory. reprint
32.	High performance antimony based type-II superlattice photodiodes on GaAs substrates B.M. Nguyen, D. Hoffman, E.K. Huang, P.Y. Delaunay, and M. Razeghi SPIE Porceedings, Vol. 7298, Orlando, FL 2009, p. 72981T-- April 13, 2009 In recent years, Type-II InAs/GaSb superlattices grown on GaSb substrate have achieved significant advances in both structural design and material growth, making Type-II superlattice infrared detector a rival competitor to the state-of-the-art MCT technology. However, the limited size and strong infrared absorption of GaSb substrates prevent large format type-II superlattice infrared imagers from being realized. In this work, we demonstrate type-II superlattices grown on GaAs substrates, which is a significant step toward third generation infrared imaging at low cost. The device performances of Type-II superalttice photodetectors grown on these two substrates are compared. reprint
33.	Background limited performance of long wavelength infrared focal plane arrays fabricated from type-II InAs/GaSb M-structure superlattice P.Y. Delaunay, B.M. Nguyen and M. Razeghi SPIE Porceedings, Vol. 7298, Orlando, FL 2009, p. 72981Q-- April 13, 2009 Recent advances in growth techniques, structure design and processing have lifted the performance of Type-II InAs/GaSb superlattice photodetectors. The introduction of a M-structure design improved both the dark current and R0A of Type-II photodiodes. This new structure combined with a thick absorbing region demonstrated background limited performance at 77K for a 300K background and a 2-π field of view. A focal plane array with a 9.6 μm 50% cutoff wavelength was fabricated with this design and characterized at 80K. The dark current of individual pixels was measured around 1.3 nA, 7 times lower than previous superlattice FPAs. This led to a higher dynamic range and longer integration times. The quantum efficiency of detectors without anti-reflective coating was 72%. The noise equivalent temperature difference reached 23 mK. The deposition of an anti-reflective coating improved the NEDT to 20 mK and the quantum efficiency to 89%. reprint
34.	Surface leakage reduction in narrow band gap type-II antimonide-based superlattice photodiodes E.K. Huang, D. Hoffman, B.M. Nguyen, P.Y. Delaunay and M. Razeghi Applied Physics Letters, Vol. 94, No. 5, p. 053506-1-- February 2, 2009 Inductively coupled plasma (ICP) dry etching rendered structural and electrical enhancements on type-II antimonide-based superlattices compared to those delineated by electron cyclotron resonance (ECR) with a regenerative chemical wet etch. The surface resistivity of 4×10⁵ Ω·cm is evidence of the surface quality achieved with ICP etching and polyimide passivation. By only modifying the etching technique in the fabrication steps, the ICP-etched devices with a 9.3 µm cutoff wavelength revealed a diffusion-limited dark current density of 4.1×10⁻⁶ A/cm² and a maximum differential resistance at zero bias in excess of 5300 Ω·cm² at 77 K, which are an order of magnitude better in comparison to the ECR-etched devices. reprint
35.	Background limited performance of long wavelength infrared focal plane arrays fabricated from M-structure InAs-GaSb superlattices P.Y. Delaunay, B.M. Nguyen, D. Hoffman, E.K. Huang, and M. Razeghi IEEE Journal of Quantum Electronics, Vol. 45, No. 2, p. 157-162.-- February 1, 2009 The recent introduction of a M-structure design improved both the dark current and R₀A performances of Type-II InAs-GaSb photodiodes. A focal plane array fabricated with this design was characterized at 81 K. The dark current of individual pixels was measured between 1.1 and 1.6 nA, 7 times lower than previous superlattice FPAs. This led to a higher dynamic range and longer integration times. The quantum efficiency of detectors without antireflective coating was 74%. The noise equivalent temperature difference reached 23 mK, limited only by the performance of the testing system and the read out integrated circuit. Background limited performances were demonstrated at 81 K for a 300 K background. reprint
36.	The importance of band alignment in VLWIR type-II InAs/GaSb heterodiodes containing the M-structure barrier D. Hoffman, B.M. Nguyen, E.K. Huang, P.Y. Delaunay, S. Bogdanov, P. Manukar, M. Razeghi, and V. Nathan SPIE Proceedings, San Jose, CA Volume 7222-15-- January 26, 2009 The Type-II InAs/GaSb superlattice photon detector is an attractive alternative to HgCdTe photodiodes and QWIPS. The use of p+ - pi - M - N+ heterodiode allows for greater flexibility in enhancing the device performance. The utilization of the Empirical Tight Binding method gives the band structure of the InAs/GaSb superlattice and the new M- structure (InAs/GaSb/AlSb/GaSb) superlattice allowing for the band alignment between the binary superlattice and the M- superlattice to be determined and see how it affects the optical performance. Then by modifying the doping level of the M- superlattice an optimal level can be determined to achieve high detectivity, by simultaneously improving both photo-response and reducing dark current for devices with cutoffs greater than 14.5 µm. reprint
37.	Background limited performance of long wavelength infrared focal plane arrays fabricated from M-structure InAs/GaSb superlattices P.Y. Delaunay, B.M. Nguyen, D. Hoffman, E.K. Huang, P. Manurkar, S. Bogdanov and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7222-0W-- January 26, 2009 Recent advances in the design and fabrication of Type-II InAs/GaSb superlattices allowed the realization of high performance long wavelength infrared focal plane arrays. The introduction of an Mstructure barrier between the n-type contact and the pi active region reduced the tunneling component of the dark current. The M-structure design improved the noise performance and the dynamic range of FPAs at low temperatures. At 81K, the NEDT of the focal plane array was 23 mK. The noise of the camera was dominated by the noise component due to the read out integrated circuit. At 8 µm, the median quantum efficiency of the detectors was 71%, mainly limited by the reflections on the backside of the array. reprint
38.	Inductively coupled plasma etching and processing techniques for type-II InAs/GaSb superlattices infrared detectors toward high fill factor focal plane arrays E.K. Huang, B.M. Nguyen, D. Hoffman, P.Y. Delaunay and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7222-0Z-- January 26, 2009 A challenge for Type-II InAs/GaSb superlattice (T2SL) photodetectors is to achieve high fill factor, high aspect ratio etching for third generation focal plane arrays (FPAs). Initially, we compare the morphological and electrical results of single element T2SL photodiodes after BCl₃/Ar inductively coupled plasma (ICP) and electron cyclotron resonance (ECR) dry etching. Using a Si₃N₄ hard mask, ICP-etched structures exemplify greater sidewall verticality and smoothness, which are essential toward the realization of high fill factor FPAs. ICP-etched single element devices with SiO₂ passivation that are 9.3 µm in cutoff wavelength achieved vertical sidewalls of 7.7 µm in depth with a resistance area product at zero bias of greater than 1,000 Ω·cm² and maximum differential resistance in excess of 10,000 Ω·cm² at 77 K. By only modifying the etching technique in the fabrication steps, the ICP-etched photodiodes showed an order of magnitude decrease in their dark current densities in comparison to the ECR-etched devices. Finally, high aspect ratio etching is demonstrated on mutli-element arrays with 3 µm-wide trenches that are 11 µm deep. reprint
39.	Band edge tunability of M-structure for heterojunction design in Sb based Type-II superlattice photodiodes B.M. Nguyen, D. Hoffman, P.Y. Delaunay, E.K. Huang, M. Razeghi, and J. Pellegrino Applied Physics Letters, Vol. 93, No. 16, p. 163502-1-- October 20, 2008 We present theoretically and experimentally the effect of the band discontinuity in Type-II misaligned InAs/GaSb superlattice heterodiodes. Calculations using the empirical tight binding method have shown the great flexibility in tuning the energy levels of the band edge in M-structure superlattice as compared to the standard InAs/GaSb superlattice. Through the experimental realization of several p-pi-M-n photodiodes, the band discontinuity alignment between the standard binary-binary superlattice and the M-structured superlattice was investigated via optical characterization. The agreement between the theoretical predictions and the experimental measurement confirms the capability of controlling the M-structure band edges and suggests a way to exploit this advantage for the realization of heterostructures containing an M-structured superlattice without bias dependent operation. reprint
40.	Background limited long wavelength infrared type-II InAs/GaSb superlattice photodiodes operating at 110 K B.M. Nguyen, D. Hoffman, E.K. Huang, P.Y. Delaunay, and M. Razeghi Applied Physics Letters, Vol. 93, No. 12, p. 123502-1-- September 22, 2008 The utilization of the P+-pi-M-N+ photodiode architecture in conjunction with a thick active region can significantly improve long wavelength infrared Type-II InAs/GaSb superlattice photodiodes. By studying the effect of the depletion region placement on the quantum efficiency in a thick structure, we achieved a topside illuminated quantum efficiency of 50% for an N-on-P diode at 8.0 µm at 77 K. Both the double heterostructure design and the application of polyimide passivation greatly reduce the surface leakage, giving an R₀A of 416 Ω·cm² for a 1% cutoff wavelength of 10.52 µm, a Shot–Johnson detectivity of 8.1×10¹¹ cm·Hz^½/W at 77 K, and a background limited operating temperature of 110 K with 300 K background. reprint
41.	Very high performance LWIR and VLWIR type-II InAs/GaSb superlattice photodiodes with M-structure barrier B.M. Nguyen, D. Hoffman, P.Y. Delaunay, E.K. Huang and M. Razeghi SPIE Proceedings, Vol. 7082, San Diego, CA 2008, p. 708205-- September 3, 2008 LWIR and VLWIR type-II InAs/GaSb superlattice photodetectors have for long time suffered from a high dark current level and a low dynamic resistance which hampers the its emergence to the infrared detection and imaging industry. However, with the use of M-structure superlattice, a new Type-II binary InAs/GaSb/AlSb superlattice design, as an effective blocking barrier, the dark current in type-II superlattice diode has been significantly reduced. We have obtained comparable differential resistance product to the MCT technology at the cut-off wavelength of 10 and 14μm. Also, this new design is compatible with the optical optimization scheme, leading to high quantum efficiency, high special detectivity devices for photon detectors and focal plane arrays. reprint
42.	Development of material quality and structural design for high performance type-II InAs/GaSb superlattice photodiodes and focal plane arrays M. Razeghi, B.M. Nguyen, D. Hoffman, P.Y. Delaunay, E.K. Huang, M.Z. Tidrow and V. Nathan SPIE Porceedings, Vol. 7082, San Diego, CA 2008, p. 708204-- August 11, 2008 Recent progress made in the structure design, growth and processing of Type-II InAs/GaSb superlattice photo-detectors lifted both the quantum efficiency and the R0A product of the detectors. Type-II superlattice demonstrated its ability to perform imaging in the Mid-Wave Infrared (MWIR)and Long-Wave Infrared (LWIR) ranges, becoming a potential competitor for technologies such as Quantum Well Infrared Photo-detectors (QWIP) and Mercury Cadmium Telluride (MCT). Using an empirical tight-binding model, we developed superlattices designs that were nearly lattice-matched to the GaSb substrates and presented cutoff wavelengths of 5 and 11 μm. We demonstrated high quality material growth with X-ray FWHM below 30 arcsec and an AFM rms roughness of 1.5 Å over an area of 20x20 μm2. The detectors with a 5 μm cutoff, capable of operating at room temperature, showed a R0A of 1.25 106 Ω.cm2 at 77K, and a quantum efficiency of 32%. In the long wavelength infrared, we demonstrated high quantum efficiencies above 50% with high R0A products of 12 Ω.cm2 by increasing the thickness of the active region. Using the novel M-structure superlattice design, more than one order of magnitude improvement has been observed for electrical performance of the devices. Focal plane arrays in the middle and long infrared range, hybridized to an Indigo read out integrated circuit, exhibited high quality imaging. reprint
43.	The effect of doping the M-barrier in very long-wave type-II InAs/GaSb heterodiodes D. Hoffman, B.M. Nguyen, E.K. Huang, P.Y. Delaunay, M. Razeghi, M.Z. Tidrow and J. Pellegrino Applied Physics Letters, Vol. 93, No. 3, p. 031107-1-- July 21, 2008 A variation on the standard homo-diode Type-II superlattice with an M-barrier between the pi-region and the n-region is shown to suppress the dark currents. By determining the optimal doping level of the M-superlattice, dark current densities of 4.95 mA·cm^-2 and quantum efficiencies in excess of 20% have been demonstrated at the moderate reverse bias of 50 mV; allowing for near background-limited performance with a Johnson-noise detectivity of 3.11×10¹⁰ Jones at 77 K for a 14.58 µm cutoff wavelength for large area diodes without passivation. This is comparable to values for the state-of-the-art HgCdTe photodiodes. reprint
44.	High-Performance Focal Plane Arrays Based on InAs-GaSb Superlattices with a 10-micron Cutoff Wavelegth P.Y. Delaunay, B.M. Nguyen, D. Hoffman and M. Razeghi IEEE Journal of Quantum Electronics, Vol. 44, No. 5, p. 462-467-- May 1, 2008 We report on the demonstration of a focal plane array based on Type-II InAs/GaSb superlattices grown on N-type GaSb substrate with a 50%-cutoff wavelength at 10 μm. The surface leakage occurring after flip-chip bonding and underfill in the Type-II devices was suppressed using a double heterostructure design. The R₀A of diodes passivated with SiO₂ was 23 Ω·cm² after underfill. A focal plane array hybridized to an Indigo readout integrated circuit demonstrated a noise equivalent temperature difference of 33 mK at 81 K, with an integration time of 0.23 ms. reprint
45.	High quantum efficiency two color type-II InAs/GaSb n-i-p-p-i-n photodiodes P.Y. Delaunay, B.M. Nguyen, D. Hoffman, A. Hood, E.K. Huang, M. Razeghi, and M.Z. Tidrow Applied Physics Letters, Vol. 92, No. 11, p. 111112-1-- March 17, 2008 A n-i-p-p-i-n photodiode based on type-II InAs/GaSb superlattice was grown on a GaSb substrate. The two channels, with respective 50% of responsivity cutoff wavelengths at 7.7 and 10 µm, presented quantum efficiencies (QEs) of 47% and 39% at 77 K. The devices can be operated as two diodes for simultaneous detection or as a single n-i-p-p-i-n detector for sequential detection. In the latter configuration, the QEs at 5.3 and 8.5 µm were measured as high as 40% and 39% at 77 K. The optical cross-talk between the two channels could be reduced from 0.36 to 0.08 by applying a 50 mV bias. reprint
46.	Recent advances in LWIR type-II InAs/GaSb superlattice photodetectors and focal plane arrays at the Center for Quantum Devices M. Razeghi, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E.K. Huang, and M.Z. Tidrow SPIE Porceedings, Vol. 6940, Orlando, FL 2008, p. 694009-- March 17, 2008 In recent years, Type-II InAs/GaSb superlattice photo-detectors have experienced significant improvements in material quality, structural designs, and imaging applications. They now appear to be a possible alternative to the state-of-the-art HgCdTe (MCT) technology in the long and very long wavelength infrared regimes. At the Center for Quantum Devices,we have successfully realized very high quantum efficiency, very high dynamic differential resistance R0A - product LWIR Type – II InAs/GaSb superlattice photodiodes with efficient surface passivation techniques. The demonstration of high quality LWIR Focal Plane Arrays that were 100 % fabricated in - house reaffirms the pioneer position of this university-based laboratory. reprint
47.	Room temperature continuous wave operation of quantum cascade lasers with watt-level optical power Y. Bai, S.R. Darvish, S. Slivken, W. Zhang, A. Evans, J. Nguyen and M. Razeghi Applied Physics Letters, Vol. 92, No. 10, p. 101105-1-- March 10, 2008 We demonstrate quantum cascade lasers at an emitting wavelength of 4.6 µm, which are capable of room temperature, high power continuous wave (cw) operation. Buried ridge geometry with a width of 9.8 µm was utilized. A device with a 3 mm cavity length that was epilayer-down bonded on a diamond submount exhibited a maximum output power of 1.3 W at room temperature in cw operation. The maximum output power at 80 K was measured to be 4 W, with a wall plug efficiency of 27%. reprint
48.	Overview of Quantum Cascade Laser Research at the Center for Quantum Devices S. Slivken, A. Evans, J. Nguyen, Y. Bai, P. Sung, S.R. Darvish, W. Zhang and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 69000B-1-8.-- February 1, 2008 Over the past several years, our group has endeavored to develop high power quantum cascade lasers for a variety of remote and high sensitivity infrared applications. The systematic optimization of laser performance has allowed for demonstration of high power, continuous-wave quantum cascade lasers operating above room temperature. In the past year alone, the efficiency and power of our short wavelength lasers (~4.8 µm) has doubled. In continuous wave at room temperature, we have now separately demonstrated ~10% wallplug efficiency and ~700 mW of output power. Up to now, we have been able to show that room temperature continuous wave operation with > 100 mW output power in the 3.8 < λ < 11.5 µm wavelength range is possible. reprint
49.	Substrate removal for high quantum efficiency back side illuminated type-II InAs/GaSb photodetectors P.Y. Delaunay, B.M. Nguyen, D. Hoffman and M. Razeghi Applied Physics Letters, Vol. 91, No. 23, p. 231106-- December 3, 2007 A substrate removal technique using an InAsSb etch stop layer improves by a factor of 2 the quantum efficiency of back side illuminated type-II InAs/GaSb superlattice photodetectors. After etching of the GaSb substrate with a CrO₃ based solution, the quantum efficiency of the diodes presents Fabry-Pérot oscillations averaging at 56%. Due to the confinement of the infrared light inside the devices, the quantum efficiency for certain devices reaches 75% at 8.5 µm. The implementation of this new technique to a focal plane array resulted in a decrease of the integration time from 0.23 to 0.08 ms. reprint
50.	Research activity on Type-II InAs/GaSb superlattice for LWIR detection and imaging at the Center for Quantum Devices M. Razeghi and B.M. Nguyen American Institute of Physics Conference Proceedings Vol. 949, Issue 1, p. 35-42, 6th International Workshop on Information Optics (WIO'07), Reykjavik, Iceland, June 25-30, 2007-- October 24, 2007 Type-II superlattice photodetectors have recently experienced significant improvements in both theoretical structure design and experimental realization. Empirical Tight Binding Method was initiated and developed for Type-II superlattice. A new Type-II structure, called M-structure, was introduced and theoretically demonstrated high R₀A, high quantum efficiency. Device design and growth condition were optimized to improve the performance. As a result, a 54% quantum efficiency, a 12 Ω·cm² R₀A were achieved for 11 µm cut-off photodetector at 77 K. Effective surface passivation techniques for MWIR and LWIR Type-II superlattice were developed. FPA imaging at MWIR and LWIR were demonstrated with a capability of imaging up to room temperature and 211 K respectively. The noise equivalent temperature difference presented a peak at 50 mK for MWIR FPA at 121 K and 26 mK for LWIR FPA at 81 K. reprint

Page 2 of 3: Prev << 1 2 3 >> Next (73 Items)