Center for Quantum Devices - Journal Articles and Conference Proceedings

Page 2 of 2: Prev << 1 2 (43 Items)

26.	High-power, room-temperature and continuous-wave operation of distributed-feedback quantum-cascade lasers at λ = 4.8 µm J.S. Yu, S. Slivken, S.R. Darvish, A. Evans, B. Gokden and M. Razeghi Applied Physics Letters, 87 (4)-- July 25, 2005 The authors present high-power continuous-wave (cw) operation of distributed-feedback quantum-cascade lasers. Continuous-wave output powers of 56 mW at 25 °C and 15 mW at 40 °C are obtained. Single-mode emission near 7.8 µm with a side-mode suppression ratio of >=30 dB and a tuning range of 2.83 cm⁻¹ was obtained between 15 and 40 °C. The device exhibits no beam steering with a full width at half maximum of 27.4° at 25 °C in cw mode. reprint
27.	Short Wavelength (λ~ 4.3 μm) High-Performance Continuous-Wave Quantum-Cascade Lasers J.S. Yu, A. Evans, S. Slivken, S.R. Darvish, and M. Razeghi IEEE Photonics Technology Letters, 17 (6)-- June 1, 2005 We report continuous-wave (CW) operation of a 4.3-μm quantum-cascade laser from 80 K to 313 K. For a high-reflectivity-coated 11-μm-wide and 4-mm-long laser, CW output powers of 1.34 W at 80 K and 26 mW at 313 K are achieved. At 298 K, the CW threshold current density of 1.5 kA/cm² is observed with a CW output power of 166 mW and maximum wall-plug efficiency of 1.47%. The CW emission wavelength varies from 4.15 μm at 80 K to 4.34 μm at 298 K, corresponding to a temperature-tuning rate of 0.87 nm/K. The beam full-width at half-maximum values for the parallel and the perpendicular far-field patterns are 26° and 49° in CW mode, respectively. reprint
28.	Beam Steering in High-Power CW Quantum Cascade Lasers W.W. Bewley, J.R. Lindle, C.S. Kim, I. Vurgaftman, J.R. Meyer, A.J. Evans, J.S. Yu, S. Slivken, and M. Razeghi IEEE Journal of Quantum Electronics, 41 (6)-- June 1, 2005 We report the light-current (L-I), spectral, and far-field characteristics of quantum cascade lasers (QCLs) with seven different wavelengths in the λ=4.3 to 6.3 μm range. In continuous-wave (CW) mode, the narrow-stripe (≈13 μm) epitaxial- side-up devices operated at temperatures up to 340 K, while at 295 K the CW output power was as high as 640 mW with a wallplug efficiency of 4.5%. All devices with λ≥4.7 μm achieved room-temperature CW operation, and at T=200 K several produced powers exceeding 1 W with ≈10% wallplug efficiency. The data indicated both spectral and spatial instabilities of the optical modes. For example, minor variations of the current often produced nonmonotonic hopping between spectra with envelopes as narrow as 5-10 nm or as broad as 200-250 nm. Bistable beam steering, by far-field angles of up to ±12° from the facet normal, also occurred, although even in extreme cases the beam quality never became worse than twice the diffraction limit. The observed steering is consistent with a theory for interference and beating between the two lowest order lateral modes. We also describe simulations of a wide-stripe photonic-crystal distributed-feedback QCL, which based on the current material quality is projected to emit multiple watts of CW power into a single-mode beam at T=200 K. reprint
29.	High-Power CW Mid-IR Quantum Cascade Lasers J.R. Meyer, W.W. Bewley, J.R. Lindle, I. Vurgaftman, A.J. Evans, J.S. Yu, S. Slivken, and M. Razeghi SPIE Conference, Jose, CA, -- January 22, 2005 We report the cw operation of quantum cascade lasers that do not require cryogenic cooling and emit at λ = 4.7-6.2 µm. At 200 K, more than 1 W of output power is obtained from 12-µm-wide stripes, with a wall-plug efficiency (η_wall) near 10%. Room-temperature cw operation has also been demonstrated, with a maximum output power of 640 mW (η_wall = 4.5%) at 6 µm and 260 mW (η_wall = 2.3%) at 4.8 µm. Far-field characterization indicates that whereas the beam quality remains close to the diffraction limit in all of the tested lasers, in the devices emitting at 6.2 µm the beam tends to steer by as much as 5-10° degrees in either direction with varying temperature and pump current. reprint
30.	Continuous-wave operation of λ ~ 4.8 µm quantum-cascade lasers at room temperature A. Evans, J.S. Yu, S. Slivken, and M. Razeghi Applied Physics Letters, 85 (12)-- September 20, 2004 Continuous-wave (cw) operation of quantum-cascade lasers emitting at λ~4.8 µm is reported up to a temperature of 323 K. Accurate control of layer thickness and strain-balanced material composition is demonstrated using x-ray diffraction. cw output power is reported to be in excess of 370 mW per facet at 293 K, and 38 mW per facet at 323 K. Room-temperature average power measurements are demonstrated with over 600 mW per facet at 50% duty cycle with over 300 mW still observed at 100% (cw) duty cycle. reprint
31.	High-Power Continuous-Wave Operation of Quantum-Cascade Lasers Up to 60 °C J.S. Yu, A. Evans, J. David, L. Doris, S. Slivken and M. Razeghi IEEE Photonics Technology Letters, 16 (3)-- March 1, 2004 High-temperature high-power continuous-wave (CW) operation of high-reflectivity-coated 12 μm wide quantum-cascade lasers emitting at λ = 6 μm with a thick electroplated Au top contact layer is reported for different cavity lengths. For a 3 mm long laser, the CW optical output powers of 381 mW at 293 K and 22 mW at maximum operating temperature of 333 K (60°C) are achieved with threshold current densities of 1.93 and 3.09 kA/cm², respectively. At 298 K, the same cavity gives a maximum wall plug efficiency of 3.17% at 1.07 A. An even higher CW optical output power of 424 mW at 293 K is obtained for a 4-mm-long laser and the device also operates up to 332 K with an output power of 14 mW. Thermal resistance is also analyzed at threshold as a function of cavity length. reprint
32.	Ridge-Width Dependence on High-Temperature Continuous-Wave Quantum-Cascade Laser Operation S. Slivken, J.S. Yu, A. Evans, L. Doris, J. David, and M. Razeghi IEEE Photonics Technology Letters, 16 (3)-- March 1, 2004 We report continuous-wave (CW) operation of quantum-cascade lasers (λ=6 μm) up to a temperature of 313 K (40°C). The maximum CW optical output powers range from 212 mW at 288 K to 22 mW at 313 K and are achieved with threshold current densities of 2.21 and 3.11 kA/cm2, respectively, for a high-reflectivity-coated 12-μm-wide and 2-mm-long laser. At room temperature (298 K), the power output is 145 mW at 0.87 A, corresponding to a power conversion efficiency of 1.68%. The maximum CW operating temperature of double-channel ridge waveguide lasers mounted epilayer-up on copper heatsinks is analyzed in terms of the ridge width, which is varied between 12 and 40 μm. A clear trend of improved performance is observed as the ridge narrows. reprint
33.	High Power, Room Temperature, Continuous-Wave Operation of Quantum Cascade Lasers Grown by GasMBE A. Evans, J. David, L. Doris, J.S. Yu, S. Slivken and M. Razeghi SPIE Conference, Jose, CA, Vol. 5359, pp. 188-- January 25, 2004 Very high power continuous-wave quantum cascade lasers are demonstrated in the mid-infrared (3 - 6 µm) wavelength range. λ~6 µm high-reflectivity coated QCLs are demonstrated producing over 370 mW continuous-wave power at room temperature with continuous-wave operation up to 333 K. Advanced heterostructure geometries, including the use of a thick electroplated gold, epilayer-side heat sink and a buried-ridge heterostructure are demonstrated to improve laser performance significantly when combined with narrow laser ridges. Recent significant improvements in CW operation are presented and include the development if narrow (9 µm-wide) ridges for high temperature CW operation. GasMBE growth of the strain-balanced λ~6 µm QCL heterostructure is discussed. X-ray diffraction measurements are presented and compared to computer simulations that indicate excellent layer and compositional uniformity of the structure. reprint
34.	High-temperature high-power continuous-wave operation of buried heterostructure quantum-cascade lasers A. Evans, J.S. Yu, J. David, L. Doris, K. Mi, S. Slivken, and M. Razeghi Applied Physics Letters, 84 (3)-- January 19, 2004 We report cw operation of buried heterostructure quantum-cascade lasers (λ=6 µm) using a thick electroplated Au top contact layer and epilayer-up bonding on a copper heat sink up to a temperature of 333 K (60 °C). The high cw optical output powers of 446 mW at 293 K, 372 mW at 298 K, and 30 mW at 333 K are achieved with threshold current densities of 2.19, 2.35, and 4.29 kA/cm² respectively, for a high-reflectivity-coated, 9-µm-wide and 3-mm-long laser reprint
35.	Cavity Length Effects of High-Temperature High-Power Continuous Wave Characteristics in Quantum-Cascade Lasers J.S. Yu, A. Evans, J. David, L. Doris, S. Slivken, and M. Razeghi Applied Physics Letters, 83 (25)-- December 22, 2003 We report the cavity-length dependent high-temperature high-power cw characteristics in λ=6 µm quantum-cascade lasers with a thick electroplated Au top contact layer. For a high-reflectivity (HR) coated 15 µm wide and 3 mm long laser, the cw operation is achieved up to 313 K (40 °C) with an output power of 17 mW. At 298 K, a very high cw output power of 213 mW is obtained for a HR coated 15 µm wide and 4 mm long laser. Thermal resistance is analyzed at temperatures above 283 K for HR coated lasers with different cavities. reprint
36.	High-Power Continuous-Wave Operation of a 6 µm Quantum-Cascade Laser at Room Temperature J.S. Yu, S. Slivken, A. Evans, L. Doris, and M. Razeghi Applied Physics Letters, 83 (13)-- September 29, 2003 We report continuous-wave (cw) operation of quantum-cascade lasers (λ= 6 µm) using a thick electroplated Au top contact layer and epilayer-up bonding on a copper heat sink up to a temperature of 308 K (35 °C). The high cw optical output powers of 132 mW at 293 K and 21 mW at 308 K are achieved with threshold current densities of 2.29 and 2.91 kA/cm², respectively, for a high-reflectivity-coated 15 µm wide and 2 mm long laser. reprint
37.	Very High Average Power at Room Temperature from λ ~ 5.9 μm Quantum Cascade Lasers J.S. Yu, S. Slivken, A. Evans, J. David and M. Razeghi Virtual Journal of Nanoscale Science & Technology 26-- May 26, 2003reprint
38.	Very High Average Power at Room Temperature from λ ~ 5.9 μm Quantum Cascade Lasers J.S. Yu, S. Slivken, A. Evans, J. David and M. Razeghi Applied Physics Letters, 82 (20)-- May 19, 2003 We report a very high average output power at room temperature for quantum-cascade lasers emitting at λ ~ 5.9 µm. For high-reflectivity-coated 2-mm-long cavities, a low threshold current density of 1.7 kA/cm² was obtained at room temperature. From 300 to 400 K, the characteristic temperature (T0) was 198 K. A maximum average output power of 0.67 W was achieved. In addition, 0.56 W average output power was observed at a duty cycle of 56%. reprint
39.	High Performance Quantum Cascade Lasers at λ ~ 6 μm M. Razeghi, S. Slivken, J. Yu, A. Evans, and J. David Microelectronics Journal, 34 (5-8)-- May 1, 2003 This talk will focus on the recent efforts at the Center for Quantum Devices to deliver a high average power quantum cascade laser source at λ ~6 μm. Strain-balancing is used to reduce leakage for these shorter wavelength quantum cascade lasers. Further, the effect of reducing the doping in the injector is explored relative to the threshold current density and maximum average output power. Lastly, to demonstrate more of the potential of these devices, epilayer down bonding is explored as a technique to significantly enhance device performance. reprint
40.	High-Average-Power, High-Duty-Cycle (~6 μm) Quantum Cascade Lasers S. Slivken, A. Evans, J. David, and M. Razeghi Virtual Journal of Nanoscience & Technology 9-- December 9, 2002reprint
41.	High-Average-Power, High-Duty-Cycle (~6 μm) Quantum Cascade Lasers S. Slivken, A. Evans, J. David, and M. Razeghi Applied Physics Letters, 81 (23)-- December 2, 2002 High-power quantum cascade lasers emitting at λ = 6.1 μm are demonstrated. Accurate control of growth parameters and strain balancing results in a near-perfect lattice match, which leads to excellent material quality. Excellent peak power for uncoated lasers, up to 1.5 W per facet for a 21 μm emitter width, is obtained at 300 K for 30 period structures. The threshold current density at 300 K is only 2.4 kA/cm². From 300 to 425 K, the laser exhibits a characteristic temperature T₀ of 167 K. Next, Y₂O₃/Ti/Au mirror coatings were deposited on 1.5 mm cavities and mounted epilayer down. These lasers show an average output power of up to 225 mW at 17% duty cycle, and still show 8 mW average power at 45% duty cycle. reprint
42.	High-Power (~9 μm) Quantum Cascade Lasers S. Slivken, Z. Huang, A. Evans, and M. Razeghi Applied Physics Letters 80 (22)-- June 3, 2002 High-power quantum cascade lasers emitting at λ > 9 μm are demonstrated. Accurate control of layer thickness and interfaces is evidenced by x-ray diffraction. Excellent peak power for uncoated lasers, up to 3.5 W per facet for a 25 μm emitter width, is obtained at 300 K for 75 period structures. The threshold current density at 300 K is only 1.4 kA/cm². From 300 to 425 K, the laser exhibits a characteristic temperature, T₀, of 167 K. Over 150 mW of average power is measured per facet for a duty cycle of 6%. Simulation of the average power output reveals a thermal resistance of 12 K/W for epilayer-up mounted ridges. reprint
43.	High-Power (~9 μm) Quantum Cascade Lasers S. Slivken, Z. Huang, A. Evans, and M. Razeghi Virtual Journal of Nanoscale Science and Technology 5 (22)-- June 3, 2002reprint

Page 2 of 2: Prev << 1 2 (43 Items)